|
|
|
|
| |
|
Vauxhall
1.4L XE Basic Taper Throttle Kit - 127/137 bhp
|
|
For
1.4 Litre 16V XE Engine Distributor less
Exhaust manifold type needed to run this with this kit *A-1.6L-XE
|
| |
| This
kit is the basis for the upgrades in the 1.4L taper throttle range
& the MBE ecu comes complete with a program allowing you to be
ready to run immediately. We have had reports that adding this kit
to the standard engine can produce between 125 & 137 bhp dependant
on your engine version. |
|
|
|
| The
wiring harnesses have been specially designed to be as neat as possible
and are available in front or rear wheel drive layouts to cover as
many applications as possible, when ordering your kit you should specify
whether your car is front, rear or mid engine layout. |
|
 |
The
standard injectors fitted to the 1.4L 16v engine are unable to supply
enough fuel to cope with the improvements in power that the taper
system adds to this engine, so they have to be replaced. We use the
Bosch Blue injectors, Part No.0280 150 427, as fitted to the 2.0L
LN engine. These should be readily available from breakers yards,
if not you can buy them from us. |
|
|
|
|
|
|
Recommended
Options
|
 |
You
may wish to replace the standard Corsa coil with our more reliable
COIL-4, which suits distributor less engines. Shown left is the coil
and our specially developed bracket & adaptor plates for the 1.6L
engine. |
|
|
 |
Fuel
Regulator Options
The
kits come with a FR1 fuel pressure regulator, however if you are
anticipating upgrading the kit in the future we would recommend
you choose one of the following options;
FR2SB
Fuel
regulator with high specificiation internals with consistently accurately
maintained fuel pressure on high usage fuel systems, black top,
supplied with -6 & -8 loose couplings. (Shown right)
FR-3.5
& FR-MNT Fuel
regulator 3.5 Bar (51.45 PSI) & mounting bracket. (Shown far
right)
|
|
|
|
Fuel
Injection Options
If
you are aniticipating upgrading the to +30 bhp in the future, you
may wish to choose to use the smaller high flow peco injectors,
these require a different fuel rail which can be substituted as
part of the kit instead of the standard rail. Alternatively if you
wish to upgrade later, the fuel rail can be purchased separately.
INJ-480P
Small
Peco injector 480 high flow ywllow (14 Ohm)
TP30-P2
Fuel rail for Peco injectors -6 ends
|
|
|
|
 |
Barometric
Sensors
If
you are likely to be using the engine in situations when you are
at altitude ie. travelling abroad in the mountains, then you'll
need to run this sensor to adjust the fuel mixture to compensate.
LM-BAR-ADP-01
Barometric
adaptor lead to upgrade off the shelf harness
BARO-SEN-1
Barometric pressure sensor
|
|
|
|
You
may wish to upgrade the rod bolts to heavy duty bolts which will
allow you to increase the rev limit from 7250 to 7750.
RB2K
Heavy
duty ARP rod bolt set 1.4l/1.6L XE + instructions
|
|
|
|
|
|
|
These
kits will only yield their true potential when used in conjunction with
our exhaust manifold or one made to our design and a suitable exhaust
system, please click on the relevant description below for more information.
The recommended manifold is stated at the beginning of each upgrade.
|
| |
|
|
|
|
|
|
|
|
|
|
SBD
Motorsport Ltd, Unit 15, Red Lion Business Park, Red Lion Road, Surbiton,
Surrey. KT6 7QD. Tel: 0208 391 0121.
|
|
|